Difference between revisions of "External Maintenance"

From The Bike Kitchen
Jump to: navigation, search
(transfer of page content from old wiki)
m (Wonderificdave moved page Basic Maintenance to External Maintenance: Class was renamed long long ago)
 
(8 intermediate revisions by 3 users not shown)
Line 1: Line 1:
−
The Bike Kitchen periodically offers a tune-up class, covering the following topics, among others:
+
=Curriculum=
  
−
* Cleaning a bicycle
+
==Day 1 : Flat Repair==
−
* Replacing cables and cable housing
 
−
* Adjusting deraillers and brakes
 
−
* Wrapping handlebar tape
 
−
* Disassembling, lubing and adjusting bearing surfaces (headset, hubs, bottom bracket)
 
−
* Truing wheels
 
  
−
==Class Planning==
+
Bicycle Anatomy
 +
* Frame tubes
 +
* Components
 +
* Brief quiz
  
−
Generally, the class is conducted over four sessions of 3 hours each, or 5 sessions of 2 1/2 hours each. Class enrollment is limited to around 8 students, due to limited numbers of stands and [toolkits>Main.Toolkits]. It's up to one person to take the initiative to organize the class, but two instructors per night are recommended to handle the demonstration and students' questions.  We've had problems in the past with flaky instructors, so if you plan on teaching a class, set the dates and times and commit to following through to the end of the class.  Also, it's good to commit to being available to your students during some of the regular open hours while the class is in session.
+
===Basic Chain Maintenance===
  
−
Enrollment is generally handled through email, on a first-come first-serve basis. Start contacting people on a waitlist, provided by the last instructor, and bike kitchen patrons. If the waitlist fails to fill the class, a small posting on the [SFBC>http://sfbike.org] mailing list should generate more than enough interest. Try the following format:
+
Types of Lubricants
 +
* Dry vs. Wet; describe, compare
 +
* Different types of dry: teflon, parafin, silicon, plastic
 +
* Wet on dry ok; dry on wet not ok
  
−
<pre>
+
Lubricating vs. Cleaning
−
HOMEMADE TUNE-UPS AT THE BIKE KITCHEN
+
* How often, how do you know when
 +
* Basic lubrication; keep it slightly glistening
 +
* Light cleaning; rinse the dirt out w/ lube
 +
* Remove, soak and scrub
 +
* Remove all solvent before lubricating
  
−
<DAY>, <DATE RANGE>, <TIME>; Bike Kitchen, 18th & Alabama
+
===Flat Repair===
  
−
This hands-on class will teach everything you need to know about keeping your bike in
+
Tire/Rim Anatomy
−
working order under normal wear and tear, including brake adjustment, wheel truing, hub
+
* Bead; materials
−
adjustment, drive-train and frame cleaning, and more. The class includes 5 sessions on
+
* Rim hook
−
<DAY OF WEEK> evenings starting <START DATE>. No experience is necessary, but you need a
+
* Engagement
−
bike to work on that needs a tune-up. Registration is a suggested $80, plus parts as
 
−
necessary. Class enrollment is limited to 8 students so that everyone has tools and a
 
−
stand, so respond soon! For registration or questions, email the instructor,
 
−
<INSTRUCTOR>, at <EMAIL>.
 
−
</pre>
 
  
−
After receiving inquiries, followup with an email for each student. Ask them what type of bike they have and what condition it's in. Inform them that they need to arrive promptly, and that tuition is due in cash on the first day. Answer any questions they have, and let them know that their spot in the class is reserved pending their commitment to attend every class.
+
Types of Valves
 +
* Identification
 +
* Operation
 +
* Rim compatibility; adapter gasket
 +
* Pump compatibility
  
−
==Schedule Overview==
+
Removing Wheel
 +
* Open brake
 +
* Proper gear; reasons
  
−
This is intended only as a suggestion, for a 5-week class with 2 1/2 hour sessions. Each class should consist of demonstrations of tune-up procedures, followed by the students working on their own bikes, with the instructors circulating to provide help. Either demonstrate the procedures all at once and then let them loose, or break up the demos to keep the students more engaged, at the risk of having to deal with cans of worms.
+
Removing Tire
 +
* Use of levers
 +
* User of hands
 +
* Stubborn tire tricks
 +
* Avoid puncture
 +
* Don't user metal levers
  
−
===Day 1 - Introduction, Cleaning===
+
Finding the Leak
 +
* Types of flats
 +
* Relative orientation of tire/tube
 +
* Finding leak; circle it
 +
* Checking tire
  
−
Tools and parts needed:
+
Patching
 +
* Types of patches ; glue-on, self-adhesive
 +
* Vulcanization reaction
 +
* Prepping tube, applying glue
 +
* Applying patch
  
−
* Clean rags
+
Re-assembly
−
* Cleaning solution (Simple Green or citrus degreaser)
+
* Installing tire
−
* Chain breaker and chain cleaning bin OR
+
* Inflation steps; proper seating
−
* Chain cleaning tool
+
* Installing wheel on bike
−
* Replacement chain links, or master links
 
−
* Freewheel and cassette removal tools (splines) and chain whip
 
−
* Drivetrain brushes
 
−
* Chain lube, or other thin oil
 
  
−
Plan:
+
==Day 2 : Gears==
  
−
* Take tuition (sliding scale from $40-80) and fill out membership forms
+
===Chain Replacement===
−
* Consider distributing some course materials.  See the attached files at the end of this page for some primitive ideas.  Feel free to upload more files too.
 
−
* Make introductions -- each person should give their name and briefly describe their bike and how they use it, as well as any experience they have in bike repair
 
−
* Remove the wheels and set them aside
 
−
* Clean the bicycle frame and non-drivetrain parts using a rag and cleaning solution, showing flossing techniques
 
−
* Remove chain with chainbreaker and soak in bin, or use chain cleaning tool
 
−
* Remove gear cluster and scrub all gears
 
−
* Oil freewheel mechanism, deraillers, and chain
 
−
* Reassemble bike
 
  
−
==Rule #1: Avoid Cans of Worms==
+
Chain Wear
 +
* Indicator tool
 +
* Stretch
 +
* Cog wear, chain rings
 +
* Behavior/interaction of worn parts; skipping, stiff link
 +
 
 +
Chain Anatomy
 +
* Plates; inner, outer
 +
* Pin; flanged ends
 +
* "Link"; actually 2 segments
 +
* Sizes; road, 10spd, BMX/Track
 +
 
 +
Chain Breaker
 +
* Basic Principle; small vice
 +
* Different sizes; road/10spd, BMX/Track
 +
* Difference between upper and lower slots; upper spreads chain, lower compresses chain
 +
* Don't push the pin out!
 +
* Breaking* one step; joining* 2 steps
 +
* How to tell when it's correct
 +
 
 +
===Gears===
 +
 
 +
Cable Principles
 +
* Tension/Compression
 +
* Barrel Adjusters; 'loosening' the adjuster means 'tightening' the cable; start in the middle
 +
 
 +
Shifting Principles
 +
* Friction vs. Index
 +
* Backlash and Overshift
 +
* Indixing is in the shifter, not the deraileur
 +
* Standards, manufacturers and inter-compatibility; GripShift
 +
 
 +
Deraileur Anatomy
 +
* Parallelogram, cage, pulleys
 +
* Wrap Adjust Screw; keeps jockey pulley from hitting large cog
 +
* Limit Screws; demonstrate functionality
 +
* Compare to front; position on seat tube
 +
 
 +
Exercise
 +
* Shift out of smallest chain ring
 +
* Disconnect cable, put all screws/barrel adjusters out of position
 +
* Adjust screws first; just a bit wider than perfect to allow for overshift
 +
* Connect cable and adjust tension
 +
* Adjust for other chain rings
 +
 
 +
Shifting Technique (time permitting)
 +
* Cross gearing
 +
* Reduce load; timing w/in pedal stroke
 +
* Shift when decelerating
 +
* Shift before hills
 +
 
 +
 
 +
==Day 3 : Brakes==
 +
 
 +
Cables/Housing Types
 +
* Cable sizes, ends
 +
* Housing sizes
 +
* Housing construction, brake vs. deraileur
 +
* Housing failure modes; why shifter is unsafe for brakes
 +
* Determining correct length; short but not too short, compare to old housing
 +
 
 +
===Brakes===
 +
 
 +
Anatomy
 +
* Road: center-pull, single-pivot, dual-pivot
 +
* Mountain: cantilever, straddle cable; linear-pull (v-brake), noodle
 +
* Release mechanism
 +
* Center adjust screw(s)
 +
* Cartridge pads
 +
* Disc
 +
 
 +
Pad Alignment
 +
* Vertical; don't touch tire, or hang off the bottom of the rim
 +
* Rotation; toe shouldn't point up or down
 +
* Flat; surface should be parallel to rim face upon contact
 +
* Toe-in; noise
 +
 
 +
Pad Maintenance
 +
* Identify old dried out pads
 +
* Filing off lip
 +
* Metal deposits
 +
* Re-surfacing; put the file on the table
 +
 
 +
Exercise
 +
* Disconnect cable, remove pads, put barrel adjusters in middle
 +
* Replace or file pads if necessary
 +
* Re-install pads and position
 +
* Re-connect cable and adjust tension
 +
 
 +
Braking Technique
 +
* Use both
 +
* Front does most of the stopping
 +
* Shift weight back for hard braking/hills
 +
* If rear wheel locks under hard braking, ease up on front rather than rear* puts more weight on rear
 +
 
 +
===Wheel Truing===
 +
 
 +
Anatomy
 +
* Spokes; diameter, butting
 +
* Nipples
 +
 
 +
Tools
 +
* Stand; 3 knobs
 +
* Dish tool
 +
* Spoke wrenches; sizes
 +
 
 +
Types of Adjustment
 +
* True
 +
* Dish
 +
* Round
 +
 
 +
Basic Principle
 +
* Which way to turn nipples
 +
* Triangle geometry
 +
* Even numbers of spokes
 +
* Turn 90d at a time; be aware of spoke twist
 +
 
 +
Technique
 +
* Pick a high spot to work on
 +
* Decide where it starts and ends
 +
* Hold on to first spoke and count the rest
 +
* Make adjustments
 +
* Continue around rest of wheel before returning to the same spot
 +
 
 +
=Rule #1: Avoid Cans of Worms=
  
 
Cans of worms are any parts or problems with the bike that threaten to eat up unexpectedly large portions of time. It's up to your discretion to decide what you can and can't handle, but you might want to avoid the following:
 
Cans of worms are any parts or problems with the bike that threaten to eat up unexpectedly large portions of time. It's up to your discretion to decide what you can and can't handle, but you might want to avoid the following:
Line 74: Line 205:
 
These problems are outside the scope of a 12-hour class, and trying to fix them is a disservice to the students and to your sanity. If you run across a can of worms, suggest that they either bring it by during open hours or take it to a local bike shop.
 
These problems are outside the scope of a 12-hour class, and trying to fix them is a disservice to the students and to your sanity. If you run across a can of worms, suggest that they either bring it by during open hours or take it to a local bike shop.
  
−
==Post Class Follow Up==
+
=Post Class Follow Up=
 +
 
 +
You may consider having your students fill out a [[http://docs.google.com/Doc?docid=0ATZLtblK5DLAZGdwZjY4OG5fM2NzNHN2cGhz&hl survey of the class]]. Put responses in the Classes folder in the office.
  
 
After you finish teaching the class, come back to this wiki page and update it with your experiences.  Also, be sure to say some summarizing words on the Yahoo group because you and your co-instructor are probably the only Bike Kitchen regulars that have contact with the class.
 
After you finish teaching the class, come back to this wiki page and update it with your experiences.  Also, be sure to say some summarizing words on the Yahoo group because you and your co-instructor are probably the only Bike Kitchen regulars that have contact with the class.
  
 
Consider recruiting a fellow Bike Kitchen mechanic to teach the next session of the class.  Tell them how fun it was!
 
Consider recruiting a fellow Bike Kitchen mechanic to teach the next session of the class.  Tell them how fun it was!

Latest revision as of 09:31, 23 February 2017

Curriculum

Day 1 : Flat Repair

Bicycle Anatomy

  • Frame tubes
  • Components
  • Brief quiz

Basic Chain Maintenance

Types of Lubricants

  • Dry vs. Wet; describe, compare
  • Different types of dry: teflon, parafin, silicon, plastic
  • Wet on dry ok; dry on wet not ok

Lubricating vs. Cleaning

  • How often, how do you know when
  • Basic lubrication; keep it slightly glistening
  • Light cleaning; rinse the dirt out w/ lube
  • Remove, soak and scrub
  • Remove all solvent before lubricating

Flat Repair

Tire/Rim Anatomy

  • Bead; materials
  • Rim hook
  • Engagement

Types of Valves

  • Identification
  • Operation
  • Rim compatibility; adapter gasket
  • Pump compatibility

Removing Wheel

  • Open brake
  • Proper gear; reasons

Removing Tire

  • Use of levers
  • User of hands
  • Stubborn tire tricks
  • Avoid puncture
  • Don't user metal levers

Finding the Leak

  • Types of flats
  • Relative orientation of tire/tube
  • Finding leak; circle it
  • Checking tire

Patching

  • Types of patches ; glue-on, self-adhesive
  • Vulcanization reaction
  • Prepping tube, applying glue
  • Applying patch

Re-assembly

  • Installing tire
  • Inflation steps; proper seating
  • Installing wheel on bike

Day 2 : Gears

Chain Replacement

Chain Wear

  • Indicator tool
  • Stretch
  • Cog wear, chain rings
  • Behavior/interaction of worn parts; skipping, stiff link

Chain Anatomy

  • Plates; inner, outer
  • Pin; flanged ends
  • "Link"; actually 2 segments
  • Sizes; road, 10spd, BMX/Track

Chain Breaker

  • Basic Principle; small vice
  • Different sizes; road/10spd, BMX/Track
  • Difference between upper and lower slots; upper spreads chain, lower compresses chain
  • Don't push the pin out!
  • Breaking* one step; joining* 2 steps
  • How to tell when it's correct

Gears

Cable Principles

  • Tension/Compression
  • Barrel Adjusters; 'loosening' the adjuster means 'tightening' the cable; start in the middle

Shifting Principles

  • Friction vs. Index
  • Backlash and Overshift
  • Indixing is in the shifter, not the deraileur
  • Standards, manufacturers and inter-compatibility; GripShift

Deraileur Anatomy

  • Parallelogram, cage, pulleys
  • Wrap Adjust Screw; keeps jockey pulley from hitting large cog
  • Limit Screws; demonstrate functionality
  • Compare to front; position on seat tube

Exercise

  • Shift out of smallest chain ring
  • Disconnect cable, put all screws/barrel adjusters out of position
  • Adjust screws first; just a bit wider than perfect to allow for overshift
  • Connect cable and adjust tension
  • Adjust for other chain rings

Shifting Technique (time permitting)

  • Cross gearing
  • Reduce load; timing w/in pedal stroke
  • Shift when decelerating
  • Shift before hills


Day 3 : Brakes

Cables/Housing Types

  • Cable sizes, ends
  • Housing sizes
  • Housing construction, brake vs. deraileur
  • Housing failure modes; why shifter is unsafe for brakes
  • Determining correct length; short but not too short, compare to old housing

Brakes

Anatomy

  • Road: center-pull, single-pivot, dual-pivot
  • Mountain: cantilever, straddle cable; linear-pull (v-brake), noodle
  • Release mechanism
  • Center adjust screw(s)
  • Cartridge pads
  • Disc

Pad Alignment

  • Vertical; don't touch tire, or hang off the bottom of the rim
  • Rotation; toe shouldn't point up or down
  • Flat; surface should be parallel to rim face upon contact
  • Toe-in; noise

Pad Maintenance

  • Identify old dried out pads
  • Filing off lip
  • Metal deposits
  • Re-surfacing; put the file on the table

Exercise

  • Disconnect cable, remove pads, put barrel adjusters in middle
  • Replace or file pads if necessary
  • Re-install pads and position
  • Re-connect cable and adjust tension

Braking Technique

  • Use both
  • Front does most of the stopping
  • Shift weight back for hard braking/hills
  • If rear wheel locks under hard braking, ease up on front rather than rear* puts more weight on rear

Wheel Truing

Anatomy

  • Spokes; diameter, butting
  • Nipples

Tools

  • Stand; 3 knobs
  • Dish tool
  • Spoke wrenches; sizes

Types of Adjustment

  • True
  • Dish
  • Round

Basic Principle

  • Which way to turn nipples
  • Triangle geometry
  • Even numbers of spokes
  • Turn 90d at a time; be aware of spoke twist

Technique

  • Pick a high spot to work on
  • Decide where it starts and ends
  • Hold on to first spoke and count the rest
  • Make adjustments
  • Continue around rest of wheel before returning to the same spot

Rule #1: Avoid Cans of Worms

Cans of worms are any parts or problems with the bike that threaten to eat up unexpectedly large portions of time. It's up to your discretion to decide what you can and can't handle, but you might want to avoid the following:

  • Serious rim problems
  • Anything bent totally out of whack
  • Excessively pitted bearing surfaces
  • Cup and cone bottom brackets
  • Suspension systems, pedal bearings
  • Anything that you are not comfortable fixing or servicing
  • Anything for which we lack the proper tools

These problems are outside the scope of a 12-hour class, and trying to fix them is a disservice to the students and to your sanity. If you run across a can of worms, suggest that they either bring it by during open hours or take it to a local bike shop.

Post Class Follow Up

You may consider having your students fill out a [survey of the class]. Put responses in the Classes folder in the office.

After you finish teaching the class, come back to this wiki page and update it with your experiences. Also, be sure to say some summarizing words on the Yahoo group because you and your co-instructor are probably the only Bike Kitchen regulars that have contact with the class.

Consider recruiting a fellow Bike Kitchen mechanic to teach the next session of the class. Tell them how fun it was!

Retrieved from "https://wiki.bikekitchen.org/index.php?title=External_Maintenance&oldid=1726"